rejection rate

英 [rɪ'dʒekʃ(ə)n reɪt] 美 [rɪ'dʒekʃ(ə)n reɪt]

网络  排除率; 退稿率; 拒绝率; 废品率; 退稿率

机械



双语例句

  1. However, a printing machine of the rejection rate of living adjustment will not be format effects are broadly similar.
    但一个印活调机的废品率不会受到幅面的影响,大致都是相近的。
  2. Objective To investigate the manipulations for patients with high risks of graft rejection during perioperative period in order to reduce the rejection rate.
    目的探讨高危角膜移植患者围手术期的处理措施,以降低术后免疫排斥反应率。
  3. Short-term ATG induction therapy with delayed administration of calcineurin inhibitors led to a more favorable rejection rate and an improved clinical course in case of a rejection episode.
    短期ATG诱导疗法同时延迟应用钙调磷酸酶抑制,使得排斥反应的发生率更低,而且一旦出现排斥反应偶发事件,临床病程可得到改善。
  4. High rejection rate of ultrasonic non-destructive testing was found for a batch of hot-rolled bridge plates.
    一批桥梁板材,轧制后钢板有探伤不合格的情况。
  5. Conclusion: The rejection rate after the corneal transplantation of long-term preserved cornea is lower, and the occurrence of the rejection is delayed.
    结论:深低温保存的大鼠角膜移植术后排斥反应发生率降低,发生时间延迟。
  6. As a result, for images with complex backgrounds, a fixed decision boundary skin-color model may lead to high false rejection rate and false detection rate.
    在复杂背景情况下,采用固定的阈值边界模型进行肤色分割将导致较大的漏检或误检。
  7. Our rejection rate is less than two percent.
    不良率不到2%。
  8. Rejection rate can be greatly reduced by employing this new developed device.
    采用这种新装置可以大大降低废品率。
  9. Analyses are also made on the rejection rate, malfunction rate as well as the failure probability of the logic voter system.
    分析了逻辑表决器系统拒动率、误动率和总的故障概率及并联储备模型的可靠性。
  10. The rejection rate decreases with accretion of pressure and cycling flux and rises with increment of temperature and mass fraction of the material.
    另外,截留率随压力和循环量的增加而增大,而随物料的质量分数和温度的增加而减小。
  11. The acute rejection rate was 18.1% and ATN rate was 18.1%;
    急性排斥反应、急性肾小管坏死发生率各为18.1%;
  12. Rejection rate of control group is 24%, man/ kidney survival rate 91%.
    对照组排斥发生率24%,人/肾存活率91%。
  13. The effects of temperature, pressure, feed rate and mass concentration of Ni~ ( 2+) on rejection rate of nickel and permeate flow rate are discussed.
    讨论了试验温度、操作压力、进料流率和溶液中Ni2+的质量浓度对Ni2+的质量截留率和透过流率的影响。
  14. Results 6 months after renal transplantation the acute rejection rate is 20% in the observation group. The man/ kidney survival rate is 93% in a year.
    结果观察组肾移植术后6个月急性排斥发生率20%,1年内人/肾存活率93%。
  15. The experiment result show that the recognition rate making use of our method is 97. 33%, and the false rejection rate ( FRR) and false acceptance rate ( FAR) can attain lower level.
    实验结果表明利用我们的方法能够完成97.33%的识别率,并且其错误接受率(FRR)和错误拒绝率(FAR)都可以达到比较低的水平。
  16. M~ 2, and rejection rate of salt is more than 99.9%.
    m2,盐截留率高于99.9%。
  17. In pterygium group, the rejection rate was 17. 6%, and no rejection occurred in corneal dermoid tumor group.
    翼状胬肉组排斥反应发生率为17.6%,角膜皮样瘤组无一例发生排斥反应。
  18. Real time tests yielded a false rejection rate of 0.47% and a false acceptance rate of zero.
    实际测试结果表明,该识别系统的错误拒绝率为047%,错误接受率为0。
  19. The analysis demonstrates that the idea can reduce the service rejection rate and improve the video server efficiency preferably.
    通过仿真实验分析表明,对视频文件分盘存储能够降低系统的服务拒绝率,更进一步地提高了视频服务器效能。
  20. The results show that at the appropriate concentration of copolymer of 12%~ 13%, with PEG-400 as additive, the membrane with high rejection rate and high water fluxes rate was prepared.
    结果表明,聚合物质量分数以12%~13%为合适的制膜浓度,以聚乙二醇PEG-400为添加剂时获得了高截留率和高水通量的超滤膜。
  21. % respectively ( both P < 0.001). Rejection rate of renal post transplantation in the positive PRA recipients was 40?% and only 17?
    PRA阳性组受者肾移植术后排斥发生率为40%,而阴性组受者仅17%,两组比较差异有显著性(P<0.001)。
  22. When both of the false accept rate and the false rejection rate are close to zero, the rejection rate was about 3%. 4.
    还可根据用户需要定制分类结果,当要求错误接受率和错误拒绝率均接近0时,拒识率约为3%。
  23. As a kind method of computer aided process design, numerical simulation of quenching process can optimize process design and reduce the rejection rate, thus improve the work efficiency apparently.
    淬火过程的数值模拟作为一种计算机辅助工艺设计方法,可以优化设计工艺、降低废品率,从而大大提高工作效率。